Last login: Sat Dec 16 11:09:22 2006 from 192.168.0.186 Sun Microsystems Inc. SunOS 5.10 Generic January 2005 Please enter SUNW_HOSTNAME: indexer unknown:indexer% unknown:indexer% unknown:indexer% unknown:indexer% unknown:indexer% power -on Warning: This system does not have any power supply redundancy. Warning: Bulk power is insufficient to power all existing system boards. Powering up centerplane: 0...power already enabled Powering up centerplane: 1...power already enabled bringup -A off Powering up system board: 0...done unknown:indexer% Trying to get bringup.lock lock... OK Checking that all other domains are down.... OK Trying to set system clock... y Bringing up domain indexer This will configure the Centerplane. Please confirm (y/n)? y Configuring the centerplane, POST args -C Starting: hpost -C Opening SNMP server library... Significant contents of /export/home/ssp/.postrc: # logfile Using blacklist file /var/opt/SUNWssp/etc/jes/blacklist mgroup 0.1 mgroup 0.2 mgroup 0.3 phase cplane_isolate: CP domain cluster mask clear... phase init_reset: Initial system resets... phase jtag_integ: JTAG probe and integrity test... phase mem_probe: Memory dimm probe... phase iom_probe: I/O module type probe... phase jtag_bbsram: JTAG basic test of bootbus sram... phase proc1: Initial processor module tests... phase pc/cic_reg: PC and CIC register tests... phase dtag: CIC DTAG tests... phase mem: MC register and memory tests... phase io: I/O controller tests... phase procmem2: Processor vs. memory II tests... phase lbexit: Centerplane connection tests... phase npb_mem: Non-Proc Board MC and memory tests... phase npb_iopc: Non-Proc Board IOPC register tests... phase npb_io: Non-Proc Board I/O controller tests... phase npb_cplane: Non-Proc Board centerplane connection tests... phase nmb_procmem2: Non-Mem Board Proc vs. memory II tests... phase final_config: Final configuration... Configuring in 3F, FOM = 2048.00: 4 procs, 4 Scards, 1024 MBytes. Creating OBP handoff structures... Configured in 3F with 4 processors, 4 Scards, 1024 MBytes memory. Interconnect frequency is 99.887 MHz, from SNMP MIB. Processor external frequency is 199.805 MHz, from SNMP MIB. Processor internal frequency is 399.549 MHz, from proc clk_mode probe. Boot processor is 0.0 = 0 POST (level=16, verbose=20, -C) execution time 3:13 Boot processor 0 written to /var/opt/SUNWssp/etc/jes/indexer/bootproc Updating domain indexer with bootproc 0 domainInstance 0 and interrupt vector MIB... OK Starting obp_helper -m 0 -A off... OK Starting netcon_server -p 0 ... OK Checking boot processor signatures.. OK unknown:indexer% y: Command not found unknown:indexer% netcon -g trying to connect... connected. Unlocked write permission is granted. SUNW,Ultra-Enterprise-10000, using Network Console OpenBoot 3.2.181, 1024 MB memory installed, Serial #10901755. Ethernet address 0:0:be:a6:58:fb, Host ID: 80a658fb. <#0> ok <#0> ok <#0> ok devalias disk /sbus@40,0/SUNW,socal@0,0/sf@0,0/ssd ttya /ssp-serial ssa_b_example /sbus@40,0/SUNW,soc@0,0/SUNW,pln@b0000000,XXXXXX/SUNW,ssd@0,0:a ssa_a_example /sbus@40,0/SUNW,soc@0,0/SUNW,pln@a0000000,XXXXXX/SUNW,ssd@0,0:a isp_example /sbus@40,0/QLGC,isp@0,10000/sd@0,0 net_example /sbus@40,0/qec@0,20000/qe@0,0 name aliases <#0> ok probe-scsi-all /sbus@41,0/SUNW,fas@1,8800000 Target 6 Unit 0 Removable Read Only device TOSHIBA XM-5401TASUN4XCD348512/14/95 /sbus@40,0/QLGC,isp@1,10000 Target 4 Unit 0 Disk SEAGATE ST32550W SUN2.1G041800000000 Copyright (c) 1996 Seagate All rights reserved ASA2 Target 5 Unit 0 Disk SEAGATE ST32550W SUN2.1G041800000000 Copyright (c) 1996 Seagate All rights reserved ASA2 Target e Unit 0 Processor SYMBIOS D1000 2 ac? SAF-TE1.00 <#0> ok boot /sbus@41,0/SUNW,fas@1,8800000/sd@6,0 Boot device: /sbus@41,0/SUNW,fas@1,8800000/sd@6,0 File and args: SILO /\\ Gentoo SPARC Linux InstallCD //\ \// 2006.0 \\/ boot: You are running the second stage SILO loader. From here you can boot a ramdisk or an already-installed Linux partition. Several defaults have been defined that will make things easier. The The target "gentoo" will start a 2.4-series multiprocessor kernel. To boot an existing Linux installation from the CDROM, boot with the command "gentoo root=/dev/sdaX" where sdaX is the partition where your root filesystem is. For video mode help, type "video" at the boot: prompt. If you have a Sun Blade 100 or 150 system, add the "ide=nodma" parameter, since they have very buggy IDE chipsets that can corrupt data. Type "config" to see the SILO config file. boot: gentoo Loading initial ramdisk.... bootmem_init: Scan sp_banks, init_bootmem(min[0], bootmap[1d0], max[1fe75]) free_bootmem(sp_banks:0): base[0] size[3f1fe000] free_bootmem(sp_banks:1): base[3fc00000] size[ea000] reserve_bootmem(initrd): base[3f104000] size[f7f62] reserve_bootmem(initrd): base[3f104000] size[3f1fbf62] reserve_bootmem(kernel): base[0] size[39ea50] reserve_bootmem(bootmap): base[3a0000] size[3fd0] Remapping the kernel... done. Booting Linux... mem_init: Calling free_all_bootmem(). Starting CPU 1... OK Starting CPU 2... OK Starting CPU 3... OK 11:32 pm:~ > 11:32 pm:~ > ssh ssp@ultra5 -X Password: Last login: Sat Dec 16 11:32:19 2006 from 192.168.0.186 Sun Microsystems Inc. SunOS 5.10 Generic January 2005 Please enter SUNW_HOSTNAME: indexer unknown:indexer% power -off Warning: This system does not have any power supply redundancy. Warning: Bulk power is insufficient to power all existing system boards. Domain: indexer is not active, proceeding... Powering down system board: 0...done unknown:indexer% power -on Warning: This system does not have any power supply redundancy. Warning: Bulk power is insufficient to power all existing system boards. Powering up centerplane: 0...power already enabled Powering up centerplane: 1...power already enabled Powering up system board: 0...done unknown:indexer% bringup -A off Trying to get bringup.lock lock... OK Checking that all other domains are down... NO Bringing up domain indexer Starting: hpost Opening SNMP server library... Significant contents of /export/home/ssp/.postrc: # logfile Using blacklist file /var/opt/SUNWssp/etc/jes/blacklist mgroup 0.1 mgroup 0.2 mgroup 0.3 Reading centerplane asics to obtain bus configuration... Bus configuration determined to be 3F. phase cplane_isolate: CP domain cluster mask clear... phase init_reset: Initial system resets... phase jtag_integ: JTAG probe and integrity test... phase mem_probe: Memory dimm probe... phase iom_probe: I/O module type probe... phase jtag_bbsram: JTAG basic test of bootbus sram... phase proc1: Initial processor module tests... phase pc/cic_reg: PC and CIC register tests... phase dtag: CIC DTAG tests... phase mem: MC register and memory tests... phase io: I/O controller tests... phase procmem2: Processor vs. memory II tests... phase lbexit: Centerplane connection tests... phase npb_mem: Non-Proc Board MC and memory tests... phase npb_iopc: Non-Proc Board IOPC register tests... phase npb_io: Non-Proc Board I/O controller tests... phase npb_cplane: Non-Proc Board centerplane connection tests... phase nmb_procmem2: Non-Mem Board Proc vs. memory II tests... phase final_config: Final configuration... Configuring in 3F, FOM = 2048.00: 4 procs, 4 Scards, 1024 MBytes. Creating OBP handoff structures... Configured in 3F with 4 processors, 4 Scards, 1024 MBytes memory. Interconnect frequency is 99.902 MHz, from SNMP MIB. Processor external frequency is 199.805 MHz, from SNMP MIB. Processor internal frequency is 399.610 MHz, from proc clk_mode probe. Boot processor is 0.0 = 0 POST (level=16, verbose=20) execution time 3:17 Boot processor 0 written to /var/opt/SUNWssp/etc/jes/indexer/bootproc Updating domain indexer with bootproc 0 domainInstance 0 and interrupt vector MIB... OK Starting obp_helper -m 0 -A off... OK Starting netcon_server -p 0 ... OK unknown:indexer% netcon -g trying to connect... connected. Unlocked write permission is granted. SUNW,Ultra-Enterprise-10000, using Network Console OpenBoot 3.2.181, 1024 MB memory installed, Serial #10901755. Ethernet address 0:0:be:a6:58:fb, Host ID: 80a658fb. <#0> ok <#0> ok boot /sbus@41,0/SUNW,fas@1,8800000/sd@6,0 -p Boot device: /sbus@41,0/SUNW,fas@1,8800000/sd@6,0 File and args: -p SILO /\\ Gentoo SPARC Linux InstallCD //\ \// 2006.0 \\/ Your imagename `-p' and arguments `' have either wrong syntax, or describe a label which is not present in silo.conf Type `help' at the boot: prompt if you need it and then try again. boot: gentoo Loading initial ramdisk.... bootmem_init: Scan sp_banks, init_bootmem(min[0], bootmap[1d0], max[1fe75]) free_bootmem(sp_banks:0): base[0] size[3f1fe000] free_bootmem(sp_banks:1): base[3fc00000] size[ea000] reserve_bootmem(initrd): base[3f104000] size[f7f62] reserve_bootmem(initrd): base[3f104000] size[3f1fbf62] reserve_bootmem(kernel): base[0] size[39ea50] reserve_bootmem(bootmap): base[3a0000] size[3fd0] Remapping the kernel... done. Booting Linux... mem_init: Calling free_all_bootmem(). Starting CPU 1... OK Starting CPU 2... OK Starting CPU 3... OK 13:50 work:~ > 13:50 work:~ > 13:50 work:~ > ssh ssp@ultra5 -X Password: Last login: Sat Dec 16 13:48:46 2006 from work Sun Microsystems Inc. SunOS 5.10 Generic January 2005 Please enter SUNW_HOSTNAME: indexer unknown:indexer% hostreset unknown:indexer% netcon -g trying to connect... connected. Unlocked write permission is granted. The netcon_server disconnected. trying to connect... connected. Unlocked write permission is granted. SUNW,Ultra-Enterprise-10000, using Network Console OpenBoot 3.2.181, 1024 MB memory installed, Serial #10901755. Ethernet address 0:0:be:a6:58:fb, Host ID: 80a658fb. <#0> ok <#0> ok <#0> ok probe-scsi-all /sbus@41,0/SUNW,fas@1,8800000 Target 6 Unit 0 Removable Read Only device TOSHIBA XM-5401TASUN4XCD348512/14/95 /sbus@40,0/QLGC,isp@1,10000 Target 4 Unit 0 Disk SEAGATE ST32550W SUN2.1G041800000000 Copyright (c) 1996 Seagate All rights reserved ASA2 Target 5 Unit 0 Disk SEAGATE ST32550W SUN2.1G041800000000 Console: mono PROM 80x34 Calibrating delay loop... 797.90 BogoMIPS mem_init: Calling free_all_bootmem(). Memory: 1018120k available (2000k kernel code, 496k data, 168k init) [fffff80000000000,000000003fcea000] Dentry cache hash table entries: 131072 (order: 8, 2097152 bytes) Inode cache hash table entries: 65536 (order: 7, 1048576 bytes) Mount cache hash table entries: 512 (order: 0, 8192 bytes) Buffer cache hash table entries: 65536 (order: 6, 524288 bytes) Page-cache hash table entries: 131072 (order: 7, 1048576 bytes) POSIX conformance testing by UNIFIX Entering UltraSMPenguin Mode... Starting CPU 1... Calibrating delay loop... 797.90 BogoMIPS OK Starting CPU 2... Calibrating delay loop... 797.90 BogoMIPS OK Starting CPU 3... Calibrating delay loop... 797.90 BogoMIPS OK Total of 4 processors activated (3191.60 BogoMIPS). CPU 1: synchronized TICK with master CPU (last diff -33 cycles,maxerr 978 cycles) CPU 2: synchronized TICK with master CPU (last diff -31 cycles,maxerr 982 cycles) <6>CPU 3: synchronized TICK with master CPU (last diff -38 cycles,maxerr 994 cycles) <4>Waiting on wait_init_idle (map = 0xe) CPU 3: synchronized TICK with master CPU (last diff -38 cycles,maxerr 994 cycles) <4>Waiting on wait_init_idle (map = 0xe) Waiting on wait_init_idle (map = 0xe) All processors have done init_idle PCI: Probing for controllers. SYSIO: UPA portID 40, at 0000010800000000 sbus0: Clock 25.0 MHz SYSIO: UPA portID 41, at 0000010a00000000 sbus1: Clock 25.0 MHz dma0: HME DVMA gate array Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher kbd_init: Assuming USB keyboard. pcikbd_init_hw: no 8042 found pty: 256 Unix98 ptys configured rtc_init: no PC rtc found RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx SCSI subsystem driver Revision: 1.00 qlogicfc : PCI not present esp0: IRQ 7,4b SCSI ID 7 Clk 40MHz CCYC=25000 CCF=8 TOut 167 NCR53C9XF(espfast) ESP: Total of 1 ESP hosts found, 1 actually in use. scsi0 : Sparc ESP366-HME Vendor: TOSHIBA Model: XM-5401TASUN4XCD Rev: 3485 Type: CD-ROM ANSI SCSI revision: 02 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0 esp0: target 6 asynchronous sr0: scsi-1 drive Uniform CD-ROM driver Revision: 3.12 Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 8192 buckets, 128Kbytes TCP: Hash tables configured (established 65536 bind 65536) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 991k freed VFS: Mounted root (ext2 filesystem) readonly. Mounted devfs on /dev Warning: unable to open an initial console. Kernel panic: Attempted to kill init! Press L1-A to return to the boot prom The netcon_server disconnected. trying to connect... connected. Unlocked write permission is granted. SUNW,Ultra-Enterprise-10000, using Network Console OpenBoot 3.2.181, 1024 MB memory installed, Serial #10901755. Ethernet address 0:0:be:a6:58:fb, Host ID: 80a658fb. <#0> ok <#0> ok <#0> ok <#0> ok boot /sbus@41,0/SUNW,fas@1,8800000/sd@6,0 Boot device: /sbus@41,0/SUNW,fas@1,8800000/sd@6,0 File and args: SILO Version 1.4.13 \ ---------------------------------------------------- Welcome to the Gentoo/Linux SPARC64 InstallCD 2006.1 ---------------------------------------------------- boot: 2616 2617 config video help parameters boot: 2617 -p Allocated 8 Megs of memory at 0x40000000 for kernel Loaded kernel version 2.6.17 Loading initial ramdisk (645016 bytes at 0x3FC00000 phys, 0x40C00000 virt)... / PROMLIB: Sun IEEE Boot Prom 'OBP 3.2.181 2003/08/15 11:02' PROMLIB: Root node compatible: Linux version 2.6.17-gentoo-r5 (root@bender) (gcc version 3.4.6 (Gentoo Linux 3.4.6)) #1 SMP Fri Aug 25 09:10:34 UTC 2006 ARCH: SUN4U Ethernet address: 00:00:be:a6:58:fb Remapping the kernel... done. bootmem_init: Scan pavail, choose_bootmap_pfn: kern[400000:8d6000] avoid[3fc00000:3fc9e000] choose_bootmap_pfn: Using 0 [0] init_bootmem(min[0], bootmap[0], max[1fe75]) free_bootmem(pavail:0): base[0] size[3f1fe000] free_bootmem(pavail:1): base[3fc00000] size[d0000] free_bootmem(pavail:2): base[3fcd4000] size[16000] reserve_bootmem(initrd): base[3fc00000] size[3fc9d798] reserve_bootmem(kernel): base[400000] size[4d5ee8] reserve_bootmem(bootmap): base[0] size[3fd0] memory_present(0, 0, 1f8ff) memory_present(0, 1fe00, 1fe68) memory_present(0, 1fe6a, 1fe75) Booting Linux... Built 1 zonelists Kernel command line: root=/dev/ram0 init=/linuxrc looptype=squashfs loop=/image.squashfs cdroot -p PID hash table entries: 4096 (order: 12, 32768 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 6, 524288 bytes) mem_init: Calling free_all_bootmem(). Memory: 1019120k available (2536k kernel code, 1584k data, 176k init) [fffff80000000000,000000003fcea000] Calibrating delay using timer specific routine.. 799.62 BogoMIPS (lpj=1599248) Mount-cache hash table entries: 512 CPU[0]: Caches D[sz(16384):line_sz(32)] I[sz(16384):line_sz(32)] E[sz(8388608):line_sz(64)] Using max_cache_size of 8MB Calibrating delay using timer specific routine.. 799.18 BogoMIPS (lpj=1598364) CPU[1]: Caches D[sz(16384):line_sz(32)] I[sz(16384):line_sz(32)] E[sz(8388608):line_sz(64)] CPU 1: synchronized TICK with master CPU (last diff -29 cycles,maxerr 979 cycles) Calibrating delay using timer specific routine.. 799.17 BogoMIPS (lpj=1598356) CPU[2]: Caches D[sz(16384):line_sz(32)] I[sz(16384):line_sz(32)] E[sz(8388608):line_sz(64)] CPU 2: synchronized TICK with master CPU (last diff -28 cycles,maxerr 970 cycles) Calibrating delay using timer specific routine.. 799.18 BogoMIPS (lpj=1598360) CPU[3]: Caches D[sz(16384):line_sz(32)] I[sz(16384):line_sz(32)] E[sz(8388608):line_sz(64)] CPU 3: synchronized TICK with master CPU (last diff -26 cycles,maxerr 987 cycles) Brought up 4 CPUs Total of 4 processors activated (3197.16 BogoMIPS). migration_cost=248742 checking if image is initramfs... it is Freeing initrd memory: 629k freed NET: Registered protocol family 16 PCI: Probing for controllers. SCSI subsystem initialized SYSIO: UPA portID 40, at 0000010800000000 sbus0: Clock 25.0 MHz SYSIO: UPA portID 41, at 0000010a00000000 sbus1: Clock 25.0 MHz dma0: HME DVMA gate array NET: Registered protocol family 2 IP route cache hash table entries: 8192 (order: 3, 65536 bytes) TCP established hash table entries: 32768 (order: 6, 524288 bytes) TCP bind hash table entries: 16384 (order: 5, 262144 bytes) TCP: Hash tables configured (established 32768 bind 16384) TCP reno registered Mini RTC Driver Total HugeTLB memory allocated, 0 squashfs: version 3.0 (2006/03/15) Phillip Lougher Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered <#0> ok <#0> ok boot /sbus@41,0/SUNW,fas@1,8800000/sd@6,0 Boot device: /sbus@41,0/SUNW,fas@1,8800000/sd@6,0 File and args: SILO Version 1.4.13 \ ---------------------------------------------------- Welcome to the Gentoo/Linux SPARC64 InstallCD 2006.1 ---------------------------------------------------- boot: You are running the second stage SILO loader. From here you can boot a ramdisk or an already-installed Linux partition. Several defaults have been defined that will make things easier. The target "2616" will start a 2.6.16-series kernel. The target "2617" will start a 2.6.17-series kernel. To boot an existing Linux installation from the CDROM, boot with the command "KERNEL root=/dev/sdaX" where sdaX is the partition where your root filesystem is. Replace "KERNEL" with the kernel entry of your choice above. If in doubt you can consult our hardware compatibility list for stability notes at http://www.gentoo.org/proj/en/base/sparc/sunhw.xml For video mode help, type "video" at the boot: prompt. For help on miscellaneous parameters type "parameters" at the boot: prompt. Type "config" at the boot: prompt to see the SILO config file used by this CD. boot: video Video issues on boot If you have video related problems at boot time (signal out of range or distorted video via TFT) then try some of the following suggestions; 1) Set the resolution and refresh rate in OpenBootProm At the "ok" prompt, you can view the current settings with the command "printenv output-device". It will probably just return "screen". To set it, use the following command "setenv output-device screen:r1024x768x60". This will set the framebuffer to a resolution of 1024x768 @ 60Hz refresh rate. Note that the refresh rate doesn't always carry over into the Linux framebuffer (but the resolution seems to). 2) Specify the resolution at the SILO: prompt At the "SILO: " prompt, you can append your video mode to the kernel you would pick. Example below; SILO: KERNEL video=atyfb:1024x768@60 Will boot your system with the ATI Mach64 framebuffer with a resolution of 1024x768 at 60Hz refresh rate. 3) Disable the framebuffer If you don't want any video at all, you can disable the framebuffer as shown below. This is also useful for example if you have an ATI & Matrox framebuffer in the same machine and the kernel doesn't chose the one you want to use. For ATI framebuffers SILO: KERNEL video=atyfb:off For MATROX framebuffers SILO: KERNEL video=matroxfb:off For SBUS framebuffers SILO: KERNEL video=sbus:off boot: 2616 -p console=prom Allocated 8 Megs of memory at 0x40000000 for kernel Ioaded kernel version 2.6.16 Loading initial ramdisk (644214 bytes at 0xFFC00000 phys, 0x40C00000 virt)... | PROMLIB: Sun IEEE Boot Prom 3.2.181 2003/08/15 11:02 Linux version 2.6.16-gentoo-r13 (root@bender) (gcc version 3.4.6 (Gentoo Linux 3.4.6)) #1 SMP Fri Aug 25 08:56:42 UTC 2006 ARCH: SUN4U Remapping the kernel... done. Registering callbacks... done. bootmem_init: Scan pavail, choose_bootmap_pfn: kern[400000:7ac000] avoid[ffc00000:ffc9e000] choose_bootmap_pfn: Using 0 [0] init_bootmem(min[0], bootmap[0], max[7fe75]) free_bootmem(pavail:0): base[0] size[ff1fe000] free_bootmem(pavail:1): base[ffc00000] size[d0000] free_bootmem(pavail:2): base[ffcd4000] size[16000] reserve_bootmem(initrd): base[ffc00000] size[ffc9d476] reserve_bootmem(kernel): base[400000] size[3aad98] reserve_bootmem(bootmap): base[0] size[ffd0] memory_present(0, 0, 7f8ff) memory_present(0, 7fe00, 7fe68) memory_present(0, 7fe6a, 7fe75) Booting Linux... Ethernet address: 00:00:be:a6:58:fb Built 1 zonelists Kernel command line: root=/dev/ram0 init=/linuxrc looptype=squashfs loop=/image.squashfs cdroot -p console=prom PID hash table entries: 4096 (order: 12, 131072 bytes)